The VECTOR Permanent Hair Removal System can safely remove unwanted hair.

Our amazing Vector machine is only 3” wide, 1.5” high, 5” deep and produces the same results as professional electrolysis machines that cost thousands of dollars. Now you can perform real electrolysis in your own home and not have to submit yourself to torture with a needle.

The Vector machine also offers other advantages over conventional electrolysis. During conventional electrolysis the patient has to hold a metal rod smeared with gel. With the Vector machine you only apply a resting electrode patch anywhere on the body and continue with the treatment. It is incredibly easy to operate the Vector. There is no reason to shave anymore.
 

How the VECTOR Permanent Hair Removal System Works:

Traditional Electrolysis before the VECTOR:  Electrolysis is a process in which a needle is inserted into the hair shaft and then an electrical current is passed through the hair follicle. Although hair itself is dry, below the surface of the skin it is immersed in a watery environment with a high mineral content. The electrical current from the needle causes a chemical reaction and turns the water and salt in the hair follicle into sodium hydroxide (NaOH), which is an extremely corrosive alkali. If you were to put just a drop of pure sodium hydroxide on your skin, it would instantly burn a hole right through. This sodium hydroxide dissolves the hair follicle and the papilla causing a complete and permanent destruction of hair growth.

Even though this is a highly effective procedure, it is also has many drawbacks. First of all, the insertion of a needle into the skin over and over again can be quite painful. Treatment with a needle also requires a high degree of skill, the technician must guide the needle very accurately to reach the bottom of the hair follicle. Penetrating the skin with a needle also increases chances of infection.
 

Avoid unnecessary pain with the VECTOR System

As it turns out, it is completely unnecessary to insert a needle to produce sodium hydroxide in the hair follicle. The Vector machine works by simply grasping the hair with tweezers and applying a highly conductive gel with silver chloride. Without the electrically conductive gel this process would not work, as hair cannot conduct electricity. Applying silver chloride gel to the hair above the skin allows electrical current to pass over the non-conductive portion down into the hair follicle.
 

Vector vs. Radio Frequency Devices:

Have you been sorely disappointed by that useless gadget you bought from a department store or a television infomercial? Was it not any different that simply tweezing your hair? Yes, it was a complete waste of time and money.

Radio frequency devices work on the concept that radio frequency (RF) energy gets transmitted by the electronic tweezers down the hair shaft. RF energy is similar to the energy produced in a microwave which causes a heating effect. The heat will dehydrate and coagulate the hair bulb and the papilla. Unfortunately, hair cannot conduct current and therefore radio frequency (an alternating current) will not move or flow down the hair shaft. There will be no dehydration or coagulation of the hair shaft.

There is some heating of the actual hair that is in contact with the tweezers due to friction heat caused by spinning water molecules. Heat can potentially travel down the hair shaft but none of it will actually reach the hair follicle. This is due to the fact that these devices have an FDA assigned frequency of 27.12MHz and a power output of 1.5 Watts. This wattage is so low that it takes 60 seconds of RF energy to increase the temperature of the hair follicle by 2°F.

Now consider the following; it takes at least 108°F to cause any kind of damage to the hair follicle. With the normal body temperature of 98°F, you will have to hold each hair for at least 5-6 minutes, one by one, to see any kind of result whatsoever. No one would ever make that kind of a time investment.

While lasers are now a very effective method of hair removal, this method is not permanent and the treatment is very expensive. Here is some additional information you might want to know about lasers.
 

Lasers only work on people with very light skin.  Lasers do not work on people with gray, red, or light hair.  Lasers can’t be used on sensitive skin.  Laser treatment is very painful.  Lasers can’t be used on areas with moles, freckles, or scars.  In comparison, treatment with the Vector machine works on any individual, is far less painful, and the results are permanent.

Kit includes:

• The Vector machine.
• Four resting electrode patches.
• Two ounce supply of high viscosity no-needle conductive gel.
• Alligator clip patch cord.
• Galvanic Tweezers.
• 120/240 Volt AC power cord (this item can be used on any worldwide voltage - you will only need a plug adapter if used outside of the USA)
• 10 watts
• You can also order additional accessories below, in addition to the ones already included in the kit.

Return information:  Non-returnable item for hygienic reasons.  The Vector Hair Removal System is a Class II Medical device and cannot be returned.  If you feel there may be a defect, you can return it to the manufacturer for repair or replacement. Promolife cannot accept returned Vector Hair Removal Units for any reason.  Please read warranty info that is enclosed with the device.